Universal remote codes for Hisense TV

The code for a Hisense TV depends on which universal remote you have and its version. On GE, UltraPro and Jasco-made Philips remotes with code list CL5, the Hisense list starts with 6161, 1651 and 6251, followed by 9 more; on an RCA remote with revision R271U1, it starts with 35611. Use the finder or the table below to look up your remote and version, then enter the first code and check that the remote's buttons control the TV.

Find your Hisense TV code

Choose your remote brand and its code list version, then the device you want to control.

On the sticker under the batteries or inside the battery cover.
269 brands listed for this choice.

HISENSE TV codes for GE remotes, code list CL5

  • 6161
  • 1651
  • 6251
  • 6171
  • 2081
  • 5331
  • 2211
  • 2141
  • 5341
  • 0001
  • 0671
  • 4391

Source: Jasco's code list, checked September 24, 2026. Listed in the manufacturer's order. We haven't tested these codes on a physical remote.

How to enter a code on GE CL5
  1. Open the battery compartment and find the code list version (CL3, CL4, CL5 or CL6) on the sticker under the batteries or inside the cover. Use codes from that version only.
  2. Press and hold SETUP until the red light turns on, then release it; the light stays on.
  3. Press and release the device button you want to use (for example TV, CBL, DVD or AUD). The red light blinks once and stays on.
  4. Type the first 4-digit code listed for your brand. The red light turns off after the fourth digit.
  5. Point the remote at the device and test the remote's buttons. If they do not work as expected, repeat steps 2 to 4 with the next code in the list.
  6. Repeat for each device you want to control.

Some codes control only a few of a device's functions. Jasco recommends trying the other listed codes to find one that controls more before you settle on one. See the full GE guide for the code search and reset.

Every Hisense TV code, by remote and version

Every Hisense TV code in the manufacturers' lists, by remote and version, in listed order. Checked September 24, 2026.
RemoteVersionHisense TV codes
GE, Philips, UltraPro (Jasco)CL66161, 1651, 6251, 6171, 2081, 5331, 2211, 2141, 5341, 0001, 0671, 4391
GE, Philips, UltraPro (Jasco)CL56161, 1651, 6251, 6171, 2081, 5331, 2211, 2141, 5341, 0001, 0671, 4391
GE, Philips, UltraPro (Jasco)CL46161, 1651, 6171, 2081, 5331, 2211, 2141, 5341, 0001, 0671, 4391
GE, Philips, UltraPro (Jasco)CL32081, 5331, 2211, 4671, 0671, 3671, 4381, 4391
RCAR271U135611, 44211, 67614, 78115, 59413
RCAR271U235611, 44211, 67614, 78115, 59413
RCAR341U139812, 61514, 31612, 42113, 39011
RCAR3F80213519, 14740, 14618, 12183, 15156, 15176, 15185, 14656, 11660, 11314, 11756, 13382, 14487
RCA2002210748
RCA2003710748
RCA2004710748, 11314
RCA2005210748
RCA2017410748, 11314, 12098, 12419
RCA2018911314, 12098, 12355, 12419
RCA2030110748, 11314, 12098, 12419
RCA2040110748, 11314, 12098, 12419
RCA2047310748, 11314, 12098, 12355
RCA2047410748, 11314, 12098, 12355
RCA253841314, 1660, 2098, 2355
RCA2539411314, 12098, 12355, 12419
RCA2558211314, 12098, 12183, 12355, 12419
RCA2559212098, 12183, 12355, 12419
RCA2560411314, 12098, 12183, 12355, 12419
RCA256121314, 1660, 2098, 2355
RCA2564111314, 12098, 12183, 12355, 12419
RCA2565112098, 12183, 12355, 12419
RCA2569314355, 24525, 25146
RCA2594713519, 12183, 13382
RCA2597213519, 12183, 13382
RCA2601113519, 12183, 14398, 13382
RCA2610213519, 12183, 13382
RCA262073519, 2183, 4398, 3382, 4029
RCA2621113519, 12183, 14398, 13382
RCA315030748
RCA317940748
RCA318620748
RCA2028150748, 1660, 2098, 2355
RCAD7701237
RCAD7711237

Quick answers

What is the 4-digit code for a Hisense TV?

Every GE, UltraPro and Jasco-made Philips code is 4 digits: on CL5, the Hisense list starts with 6161, 1651, 6251. On RCA remotes, only older revisions such as 31862 use 4 digits, where Hisense starts with 0748; current RCA remotes (R271U1, R341U1, R3F802) need 5 digits.

Where do I find my Hisense TV code?

The code comes from the universal remote's maker, not from the TV, so look inside the remote's battery compartment for its version (CL3 to CL6 on GE and Philips, a revision number on RCA) and use that row of the table.

Can I set it up without a code?

Usually. GE, UltraPro and Jasco-made Philips remotes have an automatic code search, and RCA's manuals for R271U1, R341U1 and R3F802 remotes describe code searches too; each tries the codes stored in the remote one by one. The steps are on the GE, Philips and RCA pages, or side by side on how to program a universal remote without a code.

How to enter the code

The key sequence depends on the remote, and for RCA on the revision. Full steps, code search and reset are on each remote's page:

  • GE and Philips (Jasco-made): hold SETUP until the red light turns on, press TV and type the 4-digit code; the light turns off. Test the remote, and try the next code if some buttons don't respond.
  • RCA: on R271U1 and R341U1, hold TV for about 2 seconds until the light stays on, release it and type the 5-digit code. On R3F802, keep holding TV while you type.

Code not working? Match the symptom

Each answer restates the manufacturer's own troubleshooting advice; the source is under each one.

The light doesn't do what the steps describe

Jasco says the most common cause is bad batteries, even brand-new ones: try a different set.

On RCA R271U1 remotes, an indicator that stays lit after the fifth digit means the code is not in that remote's lists or a step was missed. On R3F802 remotes, a POWER key that blinks four times means the same thing, or that the device key was released during entry.

Source: Universal Remotes FAQ; RCR504BE owner's manual (revision R271U1 per its code list); RCR313BE owner's manual (revision R3F802 per its code list).

Power works, but volume, input or menu buttons don't

The stored code only partly matches your device. Program the next code listed for your brand and test again; the manufacturers say several codes can work, and some control more buttons than others. A button can also fail because the device's own remote never had that feature, such as a sleep timer.

Source: Universal Remotes FAQ; How to program your remote control.

Volume works, but the channels don't change

If a cable box, satellite receiver or converter box changes your channels, the channel buttons have to control that box, not the TV. Program the box on its own device button (for example CBL or SAT) and change channels in that mode.

Source: Universal Remotes FAQ.

The menu won't open, or the arrow buttons do nothing

Jasco remotes may need shift mode: press and release SETUP, then press MENU or the arrows while the red light is blinking. On RCA R271U1 remotes, the SHIFT key turns CHAN and VOL into arrow keys and ENTER into OK; press SHIFT again to leave shift mode. If that fails, try another code for your brand.

Source: Universal Remotes FAQ; RCR504BE owner's manual (revision R271U1 per its code list).

A Roku Streaming Stick or Fire TV Stick ignores the remote

Those sticks use radio-frequency (RF) remotes, while universal remotes send infrared (IR) signals. Jasco says the STR button on its remotes controls Roku boxes that have an infrared sensor, not the Streaming Stick or any Fire TV device.

Source: Universal Remotes FAQ.

The code is rejected or has the wrong number of digits

You're probably using a list for a different version. Jasco CL codes are always 4 digits. RCA revisions R271U1, R341U1 and R3F802 use 5-digit codes, while older revisions such as 31862 use 4 digits. Check the label in the battery compartment and pick that exact version in the finder.

Source: Jasco universal remote code lists, CL3 to CL6; RCA Remote Code Finder (revision number, device brand, device type).

No code is listed for my brand, or none of the codes work

Use your remote's automatic code search (the steps are on each remote's page). It tries every code stored in the remote for that device type, so it can find a code even when your brand isn't on the printed list.

Source: Auto Code Search; RCR504BE owner's manual (revision R271U1 per its code list); RCA Remote Code Finder (revision number, device brand, device type).

The remote forgot its codes after a battery change

Jasco remotes keep programmed codes for up to 10 minutes while the batteries are out. RCA's manual warns that remotes can lose their programming during a battery change and asks you to keep the code list, so write down the codes that worked.

Source: Universal Remotes FAQ; RCR504BE owner's manual (revision R271U1 per its code list).

Codes for another TV brand, or a remote to cover them all

Own more than one TV brand? See which universal remote covers your TVs.

Sources

  • Jasco universal remote code lists, CL3 to CL6, Jasco Products, maker of GE, UltraPro and many Philips universal remotes. Checked September 24, 2026. Used for: Every GE, Philips and UltraPro code on this site, the battery-compartment label instructions and the direct code entry steps.
  • RCA Remote Code Finder (revision number, device brand, device type), VOXX Accessories (RCA remotes). Checked September 24, 2026. Used for: Every RCA code on this site, read from the data files the finder loads, in the order the finder shows them.
  • Code Lists (per-model PDFs), RCA remotes support (Jem Accessories). Checked September 24, 2026. Used for: The revision number printed on each model's code list or quick-start sheet, which gives the model-to-revision table on this site.
  • Universal Remotes FAQ, Jasco Products. Checked September 24, 2026. Used for: Troubleshooting answers (batteries, partial codes, channels, shift mode, RF streaming sticks, code saver) and the factory reset sequence.

By Rai Ansar. Drafted with AI assistance; every code and step was then checked against the linked manufacturer sources on September 24, 2026. We haven't tested these codes on a physical remote.